- Pickering Interfaces Inc.
product
PXI Solid State Multiplexer Module, Single 6-Channel, 10 A
40-666B-012
The 40-666B-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
AC Current Shunts
CSA Series
Ohm-Labs’ CSA series of ac current shunts are designed as laboratory standards for ac current measurement up to high frequencies.
-
product
AC Current Shunts
AC Current Shunts feature low uncertainty (high accuracy), low temperature coefficients and excellent stability. These shunts are purely resistive with extremely small values of reactance. The 7340 shunts may be used over a wide frequency range from DC to 100 kHz and are optimized for use with thermal converters.
-
product
AC and DC Non Inductive Current Shunt
Series A co-axial shunt and Option 02F/B shunt
Use with wattmeters, DMMs and power analyzers to extend current measurement ranges. Use with phase angle meters to enable phase angle measurements between voltage and current. Ultra low phase shift
-
product
Shunt
Shunts are used with Moving Coil Ammeters for the measurement of current in DC Circuits.
-
product
AC Power Analyzers
Measure voltage, current and power on 4 channels: DC, 1-phase AC or 3-phase ACMake more accurate power measurements: 0.05% at 50/60 HzMeasure current directly: internal shunts to 50 Arms, or with external probes or transducersAddress multiple test scenarios with isolated inputs
-
product
DC Current Shunts
DC current shunts / standards are true 4-terminal devices that precisely measure DC currents from 10 A to 10,000 A. They use special alloys in the resistive elements which are supported on an insulating base for mechanical stability. The 9230A includes special features to reduce the effects of power dissipation and associated self heating errors. These shunts are designed to operate in air at full rated current. These are the best performing, and most widely used, DC metrology shunts in the world.
-
product
Shunts
WSM alternating current measuring resistors have compared with traditional direct current shunt resistors with coaxial voltage tap significantly better high-frequency transmission characteristics. This resulted from a production engineering very complicated structural design of the active part.ISM pulse current measuring resistors allow the metrological recording of the time curve fast current changes large amplitude in the nanosecond range. The ISM are designed for the pulse current measurement with broadband oscilloscopes.
-
product
Impulse Current Measuring Shunts
ICMS
The Impulse Current Measuring Shunts ICMS are new designed tubular shunt types with best response behavior to match the high performance of the TR-AS digital recorder for comparative current measurements. A 1st partial response time less than 10ns and a settling times less than 20ns show the advantage of these shunts. They show no initial overshoot peak, no oscillations and do not need compensation box to optimize the transient behavior as known from e.g. cage shunts.
-
product
Air Core Shunt Reactors
Shunt Reactors act as absorbers of reactive power to increase energy efficiency of the power system. Shunt Reactors are inductors that are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. The shunt reactors provide inductive compensation.
-
product
L Terminal Shunt Resistor
LT
LT shunts are highly accurate manganin resistance D.C. shunts. These shunts are designed for standard current measurement of electric equipment.
-
product
Current Transformers And Shunts
Current transformers allow the different measuring devices to provide reliable and traceable data on the trends involving consumption and production processes in electrical installations. Especially designed to be installed quickly, easily and securely, meeting the most demanding expectations of today's market, covering a wide range of primary currents as well as multiple secondary outputs, both for AC and DC measurement.
-
-
-
product
High Power Precision Shunt Resistor
HPS
*Up to 250W on heat sink*Max. current limit 387AExcellent long term stability & short term stability*Low temperature coefficient of resistance (TCR)*High current sensing & reference restores in laboratories*Change - discharge test equipment for high capacity batteries*Current sources & laboratory power supplies
-
product
Shunt Voltage References
Analog Devices offers a broad line of shunt precision voltage references that combine excellent accuracy and temperature stability with low noise and small packages. These devices operate in a manner that is functionally equivalent to a Zener diode. The bias current must be set higher than the sum of the maximum quiescent current of the voltage reference and the maximum expected load current. Since shunt voltage references are typically biased with a resistor, the voltage reference can operate on a wide range of input voltages.
-
product
Water Leak Detection Equipment
Find and pinpoint leaks on a water network under paved and unpaved surfacesPrevent unnecessary excavation worksLocate the leak at valves and hydrants, in water pipes of small diameters and in hard-to-reach places by using special extra toolsIsolate parasitic noise and focus on the potential leak sound
-
product
AC Susceptibility
The AC Susceptometer option uses a small primary excitation coil to apply an AC field to a sample (typically 1mT at frequencies from 0.1 Hz 10000 Hz). A pair of secondary pick-up coils positioned close to the excitation coils are used to detect the sample response.
-
product
High Power Shunt Resistors
CS227
The CS227 is a metal foil, SOT227 resistor designed to give a high current capability. The metal foil element is situated on an insulated heatsink composed of plated copper. This assembly is then mounted into a durable plastic housing and sealed with high temperature epoxy.
-
product
Power Metering Precision Shunt Resistore
PMS
These components have E-Beam welded manganese-copper alloy elements giving high strength, stability and reliability. Low thermal EMF and TCR. Small size and minimal power loss. Minimal heat generation and surface temperature due to small total resistance. Proprietary processing technique allows very low resistance values. Ideally suited for KWh meters and sampling sensor shunts. These units are also suitable for custom design.
-
product
AC Test Transformer
Yangzhou Power Electric Co., Ltd
The AC test transformer are especially designed for testing high voltage products and components, such as cables, power transformers, gas-insulated switchgears, bushings and arresters. It is also suitable to test insulation materials. They are used to generate testing high voltage and function as part of the complete system. These systems are particularly suited for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (inductive voltage transformers).
-
product
AC Clamp Meter
Shenzhen UYIGAO Electronic Technology Co., Ltd
Measures AC voltage and current without contacting condutors.
-
product
True-RMS AC Gaussmete
Contacta Loop-FSM
True-RMS AC Gaussmeter designed to calibrate audio frequency induction loop (AFIL) systems.
-
product
AC Clamp Meters
Cambridge Instruments & Engineering Co.
A clamp meter is a clothespin-shaped instrument that can be clamped around a live wire in order to measure the current it's carrying. As a measurement principle, clamp meters detect the magnetic field emitted by current flowing in a wire in order to measure the current value.
-
product
Programmable Wide Frequency AC Power
PWF series
The PWF series is a family of programmable AC power source with wide range of adjustable frequency, developed for aerospace or military’s 400Hz and 800Hz test applications, such as lab use, compliance test, and quality assurance. The PWF series consists of L series and M series, which have different output frequency range. L series provides 45~500Hz and 0~300V output, and M series provides 300~800Hz and 0-150V output. Users can select communication interfaces of RS-485, RS-232, and optional GPIB. The PWF series also have programming sequence functions of STEP and GRADUAL modes, three phase independent control, phase angle control, and disturbance function.
-
product
AC Load Bank
XL750-XL800 Series
Mosebach Manufacturing Company
The XL750-XL800 Series load banks offer you a continuous load at various voltages in a compact, lightweight enclosure.
-
product
AC Engine Dynamometer
DA195
Power: 195 hp (145.4 kW)Torque: 682 lb-ft (924.7 Nm)Maximum Speed: 5,600 rpmConstant Torque Range: 0 - 1,500 rpmConstant Power Range: 1,500 - 2,700 rpmDecreasing Power Range: 2,700 - 5,600 rpmRotation: bi-directional
-
product
AC Voltage Testers
ALT Series test sets are designed for testing aerial lift devices (bucket trucks) but can also serve as portable, versatile all-purpose AC testers with an output of 0-60/120 kV AC @ 7 kVA, ideal for field, plant, and substation testing.
-
product
Selective AC Voltmeter
The AC Selective AC Voltmeter is designed to measure. The number of signals is eliminated.
-
product
AC Power Source
NF’s AC power sources are designed and built to deliver high-quality, high–precision AC power. In recent years, NF’s products have been used for power-supply environment testing such as immunity testing of electronic components.
-
product
AC Voltage Tester
AllWin Instrument Science and Technology Co., Ltd.
1. AC voltage tester2. TFT LCD3. PLC,RS232C,RS485 interface4. MCU control technology
